Modification of Polylactide Nonwovens with Carbon Nanotubes and Ladder Poly(silsesquioxane)

Electrospun nonwovens of poly(L-lactide) (PLLA) modified with multiwall carbon nanotubes (MWCNT) and linear ladder-like poly(silsesquioxane) with methoxycarbonyl side groups (LPSQ-COOMe) were obtained. MWCNT and LPSQ-COOMe were added to the polymer solution before the electrospinning. In addition, nonwovens of PLLA grafted to modified MWCNT were electrospun. All modified nonwovens exhibited higher tensile strength than the neat PLA nonwoven. The addition of 10 wt.% of LPSQ-COOMe and 0.1 wt.% of MWCNT to PLLA increased the tensile strength of the nonwovens 2.4 times, improving also the elongation at the maximum stress.     

Effect of absorbed pump power on the quality of output beam from monolithic microchip lasers

The dependence of the beam propagation factor (M ² parameter) with the absorbed pump power in the case of monolithic microchip laser under face-cooled configuration is extensively studied. Our investigations show that the M ₂ parameter is related to the absorbed pump power through two parameters (α and β) whose values depend on the laser material properties and laser configuration. We have shown that one parameter arises due to the oscillation of higher order modes in the microchip cavity and the other parameter accounts for the spherical aberration associated with the thermal lens induced by the pump beam. Such dependency of M ² parameter with the absorbed pump power is experimentally verified for a face-cooled monolithic microchip laser based on Nd³⁺ -doped GdVO₄ crystal and the values of α and β parameters were estimated from the experimentally measured data points.     

外FO-群

如果群 G 的所有真商群都是 FO-群,但是群 G 本身不是 FO-群,则称 G 为外 FO-群,本文将给出外 FO-群完全的结构描述．     

高折射率椭圆芯布拉格光纤的偏振特性

应用带完全匹配层边界条件的全矢量有限元方法,分析了高折射率椭圆芯布拉格光纤的偏振特性,详细讨论了光纤结构参量对模式双折射度以及群速度走离的影响,结果发现:高折射率椭圆芯布拉格光纤的模式双折射度可达10-2量级,比传统保偏光纤至少高出一个量级,并且表现出不同于传统保偏光纤的群速度走离特性;在保持较高双折射度的同时,通过合理的结构设计,可在一定的波长处灵活地获得较大的群速度走离或零走离特性,具有重要的潜在应用价值;最后,简要分析了低折射率区域的折射率变化对偏振特性的影响;研究结果有助于设计高性能的微结构保偏光纤。     

Periodic Optical Pulses in Nonlinear Optical Fibers

We discuss the problem of transmitting polarized pulses along optical fibers with variable dispersion. The dissipation and mean dispersion are assumed to be zero, which allows using the model of the vector nonlinear Schrödinger equation. We consider an optical fiber consisting of arms of equal length, which is assumed to be large. We propose an asymptotic recursive procedure for calculating the amplitude and the phase of an optical pulse propagating along the optical cable with variable dispersion.     

PREPARATION AND CATALYTIC ACTIVITY OF BIOACTIVE FIBERS

Two kinds of water-soluble metallophthalocyanines, binuclear cobalt phthalocyanine （Co2Pc2） and binuclear ferric phthalocyanine （Fe2Pc2）, were synthesized through phenylanhydride-urea route and characterized by elemental analysis and FT-IR spectra. Binuclear metallophthalocyanine derivatives （Mt2Pc2） were immobilized on silk fibers and modified viscose fibers to construct bioactive fibers of mimic enzyme. Mt2Pc2 was used as the active center of bioactive fibers, viscose and silk fibers as the microenvironments. The catalytic oxidation ability of bioactive fibers on the malodors of methanthiol and hydrogen sulfide was investigated at room temperature. The experimental results indicated that the catalytic activity of such bioactive fibers was closely correlative to the types ofbioactive fibers and substrates.     

Mutual influence of the morphology and capillary rheological properties in nylon/glass‐fiber/liquid‐crystalline‐polymer blends

Nylon‐6/glass‐fiber (GF)/liquid‐crystalline‐polymer (LCP) ternary blends with different viscosity ratios were prepared with three kinds of nylon‐6 with different viscosities as matrices. The rheological behaviors of these blends were characterized with capillary rheometry. The morphology was observed with scanning electron microscopy and polarizing optical microscopy. This study showed that although LCP did not fibrillate in binary nylon‐6/LCP blends, LCP fibrillated to a large aspect ratio in some ternary blends after GF was added. The addition of 5 wt % LCP significantly reduced the melt viscosity of nylon‐6/GF blends to such an extent that some nylon‐6/GF/LCP blends had quite low viscosities, not only lower than those of neat resins and nylon‐6/GF blends but also lower than those of corresponding nylon‐6/LCP blends. The mutual influence of the morphology and rheological properties was examined. The great reduction of the melt viscosity was considered the result of LCP fibrillation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1619–1627, 2004     

Influence of solvents on the formation of ultrathin uniform poly(vinyl pyrrolidone) nanofibers with electrospinning

Although there have been many reports on the preparation and applications of various polymer nanofibers with the electrospinning technique, the understanding of synthetic parameters in electrospinning remains limited. In this article, we investigate experimentally the influence of solvents on the morphology of the poly(vinyl pyrrolidone) (PVP) micro/nanofibers prepared by electrospinning PVP solution in different solvents, including ethanol, dichloromethane (MC) and N,N‐dimethylformamide (DMF). Using 4 wt % PVP solutions, the PVP fibers prepared from MC and DMF solvents had a shape like a bead‐on‐a‐string. In contrast, smooth PVP nanofibers were obtained with ethanol as a solvent although the size distribution of the fibers was somewhat broadened. In an effort to prepare PVP nanofibers with small diameters and narrow size distributions, we developed a strategy of using mixed solvents. The experimental results showed that when the ratio of DMF to ethanol was 50:50 (w/w), regular cylindrical PVP nanofibers with a diameter of 20 nm were successfully prepared. The formation of these thinnest nanofibers could be attributed to the combined effects of ethanol and DMF solvents that optimize the solution viscosity and charge density of the polymer jet. In addition, an interesting helical‐shaped fiber was obtained from 20 wt % PVP solution in a 50:50 (w/w) mixed ethanol/DMF solvent. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3721–3726, 2004     

Electrospinning of ultrafine cellulose acetate fibers: Studies of a new solvent system and deacetylation of ultrafine cellulose acetate fibers

Electrospinning of cellulose acetate (CA) in a new solvent system and the deacetylation of the resulting ultrafine CA fibers were investigated. Ultrafine CA fibers (∼2.3 μm) were successfully prepared via electrospinning of CA in a mixed solvent of acetone/water at water contents of 10–15 wt %, and more ultrafine CA fibers (0.46 μm) were produced under basic pH conditions. Ultrafine cellulose fibers were regenerated from the homogeneous deacetylation of ultrafine CA fibers in KOH/ethanol. It was very rapid and completed within 20 min. The crystal structure, thermal properties, and morphology of ultrafine CA fibers were changed according to the degree of deacetylation, finally to those of pure cellulose, but the nonwoven fibrous mat structure was maintained. The activation energy for the deacetylation of ultrafine CA fibers was 10.3 kcal/mol. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 5–11, 2004     

折射率温敏式光纤温度传感器的理论模型

提出了折射率温敏式光纤温度传感器的理论模型，包括子午光线和偏射光线的影响，讨论了多模光纤的弯曲损耗，理论的分析和结果与实验相当一致。